EX120 Gel-revitalizant for diesel engines, 8ml
Reference:
XA 10034
€19.60
Tax included
Product Details
| Reference |
XA 10034
|
| In stock |
39 Items
|
| Condition |
New
|
| Engine type | Diesel |
Description
Designed for wear protection and restorative repair of diesel engines, including boosted and turbocharged ones. Due to a 20% higher* concentration of the active substance, it possesses an extended capacity for restoring worn surfaces and protecting them from wear.
Forms a cermet protective coating on the surfaces of friction pairs (engine parts restore their geometry). As a result, the updated unit exceeds a new one in its operational characteristics and is guaranteed to last 2-4 times longer.
Advantages
- Restores and protects friction parts of the cylinder-piston group, crankshaft, and valve train from wear.
- Significantly reduces fuel consumption (up to 30% at idle)
- Increases oil pressure in the system to nominal
- Levels out and increases compression in cylinders
- Increases engine power, improves its throttle response
- Reduces noise and vibration levels by 10 times
- Increases the service life of components by 2-3 times
- Protects the engine from the negative consequences of "cold start"
- Improves engine operation after just 50-100 km.
- Allows engine operation during an emergency oil leak for up to 300 km
Application
Engine treatment is carried out in 3 stages:
1st stage
Inject the contents of the syringe into the oil filler neck of the engine, warmed up to operating temperature. Start the engine and ensure it idles for 5-10 min.
2nd stage
Carried out in the same order after 100-250 km of mileage
3rd stage
Carried out in the same order after 100-250 km of mileage.
Treatment is considered complete after 1500 km of mileage.
Notes
- It is not recommended to change the oil until the end of the process
- Treatment at idle is possible (4 hours – equivalent to 200 km of mileage)
- New engines with mileage up to 20,000 km should be treated in one go
- Engines after major repairs are recommended to be treated in the usual order in three stages
- A protective cermet protective coating is formed on any functional mechanism; however, if the mechanism (engine) is in a critical condition (100% wear), the destroyed parts must be replaced
Dosage
| Oil system volume, L | 3-10 | 11-20 | 21-30 |
| Number of syringes (8 ml), pcs. | 3 | 6 | 9 |
| Treatment scheme by stages | 1+1+1 | 2+2+2 | 3+3+3 |
| Number of syringes for new engines | 2 | 4 | 6 |
Capabilities
After treatment, your car is under XADO super-protection. During engine operation, the cylinder-piston group in the area of the upper "dead" center, valve train parts (cam, tappet), and sliding bearings of the crankshaft and camshaft are most susceptible to wear. The revitalizant contains building material that compensates for the wear of these parts. As a result of revitalization, a new multifunctional gradient coating with a set of necessary service characteristics and stress states is formed on the surfaces of friction pairs. Engine parts increase in volume, regaining those "hundredths" and "tenths" that were lost or worn out during operation. This is the repair effect. The resulting coating has unique properties: significant strength, high corrosion resistance, and low roughness. After revitalization, engine parts are guaranteed to last 2–4 times longer. As a result of engine revitalization, compression in the cylinders increases significantly and levels out, fuel consumption is reduced, the car's throttle response and coasting improve, and oil pumps, turbocharger units, shafts, and bushings (bearings), and cylinder mirrors are restored, and ovality is eliminated. The engine runs quietly and without vibrations. Thanks to revitalization, it can always be kept in perfect condition.
Comments (0)
No customer reviews for the moment.
You might also like
